Cutting austenitic stainless steel Ø > 35 mm

 

The CX6 L saw blade has specifically been designed for cutting austenitic stainless steel bars with a diameter larger than 35mm at very high production rates.

With its dedicated geometry, very fast cutting and good surface finish can be achieved.

Advantages:

  • New saw body design
  • Specifically developed for stainless steel solids with a diameter > 35 mm
  • Dedicated tooth geometry
  • Very high production rates

Applications:

  • Austenitic stainless steel bars with a diameter > 35 mm
  • Suggested cutting speed: 80 – 120 m/min.
  • Feed: 0,06 – 0,12 mm/tooth.
  • Soco, Tsune, Amada, Mega, Kasto, Kentai, Behringer, Exactcut, Everising

Note: Respect 10% fill ratio, use wire brush, check quality and supply of oil. Mist preferred. Check temperature of cut surface (should be cold).

Cutting Ø ≤ 35 mm stainless steel

 

CX6-S saw blades are carbide tipped and PVD coated for cutting stainless steel solids with a diameter ≤ 35 mm.

High production rates and optimal surface finish can be achieved with our dedicated geometry.

Advantages:

  • New saw body design
  • Best saw blade when cutting ferritic, martensitic and duplex stainless steel at smaller diameter ranges
  • Specifically developed for stainless steel solids with a diameter ≤ 35 mm
  • Dedicated tooth geometry

Applications:

  • Austenitic, ferritic, martensitic and duplex stainless steel bars with a diameter ≤ 35 mm
  • Suggested cutting speed: 80 – 140 m/min.
  • Feed: 0,03 – 0,05 mm/tooth.
  • Soco, Tsune, Amada, Mega, Kasto, Kentai, Behringer, Exactcut, Everising

Note: Respect 10% fill ratio, use wire brush, check quality and supply of oil. Mist preferred. Check temperature of cut surface (should be cold).

Ideal for cutting (stainless) steel tubes and sticky materials

 

Fusion NX saw blades have specifically been designed for stainless steel applications and sticky materials, but they are also suitable for cutting (thin walled) steel tubes and stainless steel flying cut-off applications.

 

Advantages:

  • Ideal for (thin walled) stainless steel tubes and sticky materials
  • Dedicated thin PVD coating
  • Reduced side pick-up
  • Very low friction coefficient
  • Wear resistant
  • Very high hardness
  • Very high temperature resistance
  • Suitable for extremely high cutting speeds and feeds
  • To be used with spray mist or emulsion coolant for maximal results
  • For relevant applications, a recoating program is available

 

Applications:

  • Ideal for cutting (stainless) steel tubes and sticky materials
  • Suggested cutting speed:
    Steel 60 – 120 m/min
    Austenitic stainless steel (300 series) 30 – 50 m/min
    Ferritic w/o Ti (409 & 412) 220 – 260 m/min
    Ferritic with Ti (441) 60 – 120 m/min
  • Machines: Automatic, semi-automatic and flying cut off applications

 

OVERVIEW DIAMETERS HSS FUSION NX SAW BLADES
Diameter
(mm)
Kerf
(mm)
Bore hole
(mm)
Teeth

 

160 1,2 / 1,6 / 2,0 32 80 / 100 / 120 / 160
175 1,6 / 2,0 32 64 / 90 / 110 / 140 / 180
200 1,2 / 1,6 / 1,8 / 2,0 32 7100 / 128 / 160 / 200
225 1,2 / 1,6 / 2,0 / 2,5 32 / 40 64 / 80 / 120 / 150 / 180 / 220
250 1,2 / 1,6 / 2,0 / 2,5 32 / 40 64 / 80 / 100 / 110 / 128 / 160 / 200 / 240
275 1,2 / 1,6 / 2,0 / 2,5 / 3,0 32 / 40 72 / 78 / 84 / 96 / 110 / 120 / 144 / 180 / 220 / 280
300 1 ,6 / 2,0 / 2,5 / 3,0 32 / 38 / 40 80 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 240 / 320
315 2,0 / 2,5 / 3,0 32 / 40 72 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 250 / 320
325 2,0 / 2,5 / 3,0 32 / 40 90 / 100 / 110 / 130 / 150 / 170 / 200 / 250 / 320
350 2,0 / 2,5 / 3,0 / 3,5 32 / 40 / 50 80 / 90 / 110 / 120 / 140 / 160 / 180 / 220 / 280 / 350
370 2,0 / 2,5 / 3,0 / 3,5 40 / 50 70 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 190 / 220 / 300
400 2,5 / 3,0 / 3,5 / 4,0 / 4,5 40 / 50 70 / 80 / 90 / 100 / 128 / 140 / 160 / 180 / 200 / 250 / 320
425 2,5 / 3,0 / 3,5 / 4,0 32 / 40 / 50 70 / 80 / 100 / 110 / 120 / 130 / 140 / 160 / 180 / 220 / 260 / 350
450 2,5 / 3,0 / 3,5 / 4,0 32 / 40 80 / 90 / 100 / 120 / 140 / 180 / 240 / 280
500 3,0 / 3,5 40 / 50 90 / 100 / 110 / 130 / 160 / 200 / 260 / 310
525 3,0 / 3,5 50 90 / 104 / 120 / 140 / 170 / 220 / 280 / 340
550 3,5 / 4,0 50 / 80 100 / 110 / 130 / 150 / 180 / 220 / 300 / 360
560 3,5 / 4,0 50 / 80 100 / 110 / 130 / 150 / 180 / 220 / 300 / 360
600 3,5 / 4,0 50 / 80 100 / 120 / 130 / 160 / 190 / 240 / 320 / 380
630 3,0 / 3,5 50 / 80 100 / 120 / 130 / 160 / 190 / 240 / 320 / 380

 

Ideal for cutting thin walled (stainless) tubes and profiles, sticky materials

 

The Power NX saw blade has specifically been designed for cutting (very) thin walled (stainless) steel tubes and profiles.

A special, temperature resistant, thin PVD coating, combined with a thinned cutting area, enables these blades to be used for extremely demanding applications, like fast cutting of thin walled products.

Advantages:

  • Especially designed for cutting stainless steel
  • Thin PVD coating with a very low friction coefficient and high hardness
  • Very suitable for extremely demanding applications
  • Low vibration
  • Less burr
  • Reduced risk of tube-end deformation
  • Very high temperature resistance
  • To be used with spray mist or emulsion coolant for maximal results
  • For relevant applications, a recoating program is available

 

Applications:

  • Cutting thin walled (stainless) tubes and profiles, sticky materials
  • Suggested cutting speed:
    Austenitic stainless steel (300 series) 30 – 50 m/min
    Ferritic w/o Ti (409 & 412) 220 – 260 m/min
    Ferritic with Ti (441) 60 – 120 m/min
  • Machines: Automatic, semi-automatic, flying cut off applications

 

OVERVIEW DIAMETERS HSS POWER NX SAW BLADES
Diameter
(mm)
Kerf
(mm)
Bore hole
(mm)
Teeth

 

160 1,2 32 80 / 100 / 120 / 160
200 1,2 32 72 / 100 / 128 / 160 / 200
225 1,2 32 / 40 64 / 80 / 120 / 150 / 180 / 220
250 1,2 / 1,6 / 1,8 / 2,0 32 / 40 64 / 80 / 100 / 110 / 128 / 160 / 200 / 240
275 1,2 / 1,8 / 2,0 / 2,5 32 / 40 72 / 78 / 84 / 96 / 110 / 120 / 144 / 180 / 220 / 280
315 1,8 / 2,0 / 2,5 32 / 40 72 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 200 / 250 / 320
350 1,8 / 2,0 / 2,2 / 2,5 / 3,0 32 / 40 / 50 80 / 90 / 110 / 120 / 140 / 160 / 180 / 220 / 280 / 350
370 1,8 / 2,0 / 2,5 / 3,0 40 / 50 70 / 80 / 90 / 100 / 110 / 120 / 140 / 160 / 190 / 220 / 300
400 2,0 / 2,2 / 2,5 / 3,0 40 / 50 70 / 80 / 90 / 100 / 128 / 140 / 160 / 180 / 200 / 250 / 320
425 2,5 / 3,0 32 / 40 / 50 70 / 80 / 100 / 110 / 120 / 130 / 140 / 160 / 180 / 220 / 260 / 350
450 2,5 / 3,0 40 / 50 80 / 90 / 100 / 120 / 140 / 180 / 240 / 280
600 3,0 50 / 80 100 / 120 / 130 / 160 / 190 / 240 / 320 / 380

 

HSS Fernox – The allround HSS Solution

 

Due to a sophisticated PVD coating for wear protection which achieves a very low friction coefficient, the Fernox saw blade is a cost efficient solution for cutting structural and non-alloy tool steel thin walled tubes.

When cutting tubes and profiles on manual and semi-automatic sawing machines, Fernox allows a higher cutting speed than a steam treated saw blade. It can even be used for cutting thin walled tubes on automatic machines.

Fernox is also very suitable for cutting stainless steel tubes and profiles.

Advantages compared to steam treated:

  • Higher blade life
  • Increased uptime
  • Lower cost per cut
  • Little to no side pick-up
  • Higher production output
  • Ideal for cutting both structural- and stainless steel

Applications:

  • All structural steel and non-alloy steel thin walled tubes
  • Tensile strength up to 600 N/mm2
  • Steel – Suggested cutting speed: 60 – 120 m/min
  • Austenitic stainless steel (300 series) – Suggested cutting speed: 30 – 50 m/min – Blade life:≈1m2
  • Ferritic w/o Ti (409 & 412) – Suggested cutting speed: 220 – 260 m/min – blade life: ≈1m2
  • Ferritic with Ti (441) – Suggested cutting speed: 60 – 120 m/min
  • Feed: 0,03 – 0,09 mm/tooth
  • Machines: manual, semi-automatic, automatic, flying cut-off applications

 

TYPICAL APPLICATION EXAMPLES HSS Eclipse
Material
type
Dimensions
(mm)
Cutting
speed

(m/min)
Cutting
time

(s)
Blade
life

(cuts)
Blade
life

(m2)
Tube, S235 18 x 1,6 180 0,4 35,000 3,0
Tube, S235 25 x 2,0 140 0,9 25,000 3,6
Tube, S235 40 x 4,0 70 3,96 5,000 2,2
Tube, S275 60 x 2,6 120 2,7 5,000 2,6

 

Orbital flying cut-off – Stainless steel

 

The TubeMaster Stainless saw blade has specifically been developed for cutting stainless steel tubes on orbital flying cut-off units.

These saw blades can cope with cutting speeds between 60 – 120 m/min.

TubeMaster Stainless offers high uptime due to a blade life up to 3,5 m2, combined with high cut quality and production output.

Applications:

  • Orbital flying cut-off applications
  • Suggested cutting speed: 60 – 120 m/min
  • Feed: 0.035 – 0.10 mm/tooth
  • TubeMaster Stainless saw blades are available for all orbital cutting machines.

Note: To accomodate higher requirements of line speed or reduce vibration level, much higher cutting speeds (up to 600 m/min) can be applied. Tooth load can be raised , while respecting max fill ratio of 10% during entry. Respect max cut depth of 3mm.

Perfect surface finish and burr-free tube ends cutting austenitic stainless steel tubes

 

The high nickel content of austenitic stainless steel tubes makes them difficult to cut with HSS saw blades.

With the dedicated tooth geometry of the carbide tipped and PVD coated CX 4 saw blade, perfect surface finish and burr-free tube ends will be achieved.

Applications:

  • High performance cutting of stainless steel tube (austenitic, ferritic)
  • Suggested cutting speed: 80 – 140 m/min
  • Tooth load: 0,06 – 0,12 mm/tooth
  • Machines: Soco, Rattunde, Bewo, RSA, Sinico

Note: Respect 10% fill ratio, use wire brush. Be aware of tube vibration when cutting less stable products (use form jaws). Choice of cutting oil is critial to achieve high blade life (Castrol B30 or B335 suggested). Positive geometry, carefull handling of saw blade to prevent tooth damage.